| 안녕하세요..
empos tiny를 가지고 테스트하고 있는데요..
tiny에서 usb host와 tft-lcd를 올리려고 커널 컴파일후
usb가 인식이 되지 않습니다.
부팅시 메세지는
---------------------------------------------------------------------
Linux version 2.4.19-rmk4-pxa2-xmodule1 (newton@localhost.localdomain) (gcc version 2.95.3 20010315 (release)) #1 2006. 12. 02. (Åä) 00:35:15 CST
CPU: Intel XScale-PXA255 revision 6
Machine: Hanback Electronics EMPOS_X255 Development Platform
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 99.53MHz (*1)
Turbo Mode clock: 199.07MHz (*2.0, active)
Security risk: creating user accessible mapping for 0x10200000 at 0xf1200000
Security risk: creating user accessible mapping for 0x10300000 at 0xf1300000
Security risk: creating user accessible mapping for 0x10600000 at 0xf1600000
Security risk: creating user accessible mapping for 0x10700000 at 0xf1700000
Security risk: creating user accessible mapping for 0x14000000 at 0xf1800000
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram rw console=ttyS0,115200 mem=64M
Relocating machine vectors to 0xffff0000
Calibrating delay loop... 198.65 BogoMIPS
Memory: 64MB = 64MB total
Memory: 56848KB available (1437K code, 273K data, 56K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 14) is a PXA UART
ttyS01 at 0x0000 (irq = 13) is a PXA UART
ttyS02 at 0x0000 (irq = 12) is a PXA UART
RTC-4513 Version 0.1 initialized.
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
SMSC LAN91C111 Driver (v2.0), (Linux Kernel 2.4 + Support for Odd Byte) 09/24/01 - by Pramod Bhardwaj (pramod.bhardwaj@smsc.com)
eth0: SMC91C11xFD(rev:1) at 0xf4000300 IRQ:0 MEMSIZE:8192b NOWAIT:0 ADDR: 00:0b:a8:06:00:ef
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
ac97_codec: AC97 Audio codec, id: 0x4352:0x5973 (Unknown)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb.c: new USB bus registered, assigned bus number 1
hc_sl811.c: USB SL811 at f1800000, addr2 = f1810000, IRQ 32
hub.c: USB hub found
hub.c: 1 port detected
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 6144K
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 56K
hub.c: USB new device connect on bus1/1, assigned device number 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 3
eth0:PHY remote fault detected
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
--------------------------------------------------------------------
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
이부분과
hub.c: USB new device connect on bus1/1, assigned device number 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 3
eth0:PHY remote fault detected
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
에러를 못잡겠네요..
CD 의 bootloader, zImage, ramdisk
한백 홈페이지 자료실의 source까지 전부다 받아서
하루종일 image 파일과 source까지 이방법 저방법 다 해봤는데..
원인을 모르겠습니다..
전에는 이런 에러가 없엇는데 오늘 갑자기 그러네요..
바쁘시더라도 꼭좀 확인해 주세요..
그리고 empos tiny의 최신버전의 소스와 이미지를 자료실에 올려주시면 감사하겠습니다. |
